Menu Close

How to Remove Water Restrictor From Delta Rainfall Shower Head?

Like any other shower fittings, modern Delta rain shower heads are designed with a removable/replicable water restrictor that controls water flow through the pipe to your shower.

Interior and washroom décor instructs that designers install water restrictors in showerheads to prevent water loss or water discharge per minute, but if you don’t like the limitation and the flow of water, it is wise to remove your restrictors.

There are many reasons why you should consider changing or removing your restrictions, and if this is one of your cases, here are some ways and steps that you can follow and achieve the same.

delta rain shower head restrictor removing

Recommend reading: Top 8 Best Handheld Shower Head for Small Shower Reviews & Buying Guides

 

Why Should you Remove your Water Restrictors From Delta Rain Shower Head?

To Improve Water Flow

Water restrictors are designed to regulate the amount of water in your showerheads. Most designs are regulated to help conserve water, and if you have enough water, then there is no need to limit your shower discharge. A system with water restrictors and some water effects on the steel pipe will reduce your shower discharge by half. Eliminating this part helps reduce water obstacles, thus giving your shower a continuous flow of water throughout.

Recommend reading: FAST and EASY Way to Raise Your Shower Head

 

Minimize Power Spending

In fluid flow, the number of fittings and elbows in a pipe increases the amount of power needed to pump water to the final destination. In a simple shower connection, there are some T-junction, elbows, and extra fittings, which help in increasing the number of the fitting. With an additional water restrictor, the sum of fittings is increased, making which increases the amount of power required. And an increase in pumping power results in an increase in power bills in your home. Eliminating this part can sound awkward, considering that water is to be conserved at all costs, but the summation of power bills with the fitting included makes it wise to consider it a good move.

Recommend reading: Easy Steps to DIY Shower Aromatherapy & Benefits

 

Improve the Showerhead Efficiency

Delta rain shower heads are designed in a way that they operate at the maximum water supply. It would help if you had a continuous flow of water, and with your restrictor, this cannot happen in place. Because most of these fittings are designed to prevent water loss but on a normal shower, trust me, what makes it the best is the continuous sprays from the showerheads. The only way to ensure you enjoy your showers is to eliminate all the fittings, and when we speak of fittings, the water restrictor is our main aim.

Recommend reading: The 10+ Best Handheld Shower Head for Elderly Reviews

 

How to Remove Water Restrictor from Delta Rainfall Showerhead?

Tools and Accessories

  • Adjustable wrench
  • Towel or cloth
  • Paper clip
  • Plumber’s tape
  • Screwdriver
  • Needle-nose pliers

Recommend reading: Top 6 Best Hand Held Shower Heads for Pressure Reviews

 

Step 1 Remove/disconnect the shower head from the pipe arm.

how to remove the water shower head step by step

To remove or disconnect your showerhead from the pipe arm that connects your Delta shower head to the wall, you need to unscrew all the fitting screws. You can do this by your own hand or use a wrench. Use the towel to protect or hold the screws and the showerhead and other important fittings. To unscrew your fitting nails or screw, you need to turn your showerhead clockwise then use a screwdriver to remove the nuts.

Recommend reading: The 5 Best Delta Oil Rubbed Bronze Shower Head Reviews

 


Step 2 Disconnect the Shower Screen

removing water restrictor step by step

Sometimes or depending on the type of showerheads, there are screens used to trap water sediments and debris inside the shower. Proceed with caution and ensure you don’t damage that sieve; you can read more on the installation manual if you have no idea about your showerheads. You might also need to gently tap the showerhead with your fingers to dislodge it or use needle-nose pliers to dislodge.

Recommend reading: Top 5 Best Delta Magnetic Shower Head Reviews with Handheld Shower Head Combo

 


Step 3 Remove the Gasket or O-Ring

how to disconnect the o-ring

Insider the showerhead; there should be a gasket or a rubber O-ring; use your paperclip and hold these rubbers in place, then pull them out. Be careful not to damage the gasket because you will have to replace it after installing and removing the water restrictor.

Recommend reading: Top 9 Best Filtered Shower Head Reviews For Hair Loss and Hair Health

 


Step 4 Remove your Water Restrictor

how to remove restrictor from Delta rain shower head

You should set your water flow restrictor; it is normally a valve-like ring located in between the gate valve and the showerhead’s ball valve. Most designs come in s star-shaped metal gadget with a plastic ring on the inside. Use your unbent paperclip, hold it tight, and pull the restrictor out slowly. If your restrictors fail to come out, it means the pipe has some sediments or other substances holding it; twist it slowly from left to right and then pull it once.

Recommend reading: Top 9 Delta Two In One Shower Head Reviews

 


Step 5 Reattach your Shower

how to reattch the shower head

Before you start to unscrew your showerhead back, it is wise to clean the old plumber’s tape using a clean cloth. Wipe all the damp inside the showerhead; you can use white vinegar to clean any rust. Remove all the deposits by scrubbing the inner grooves with a soft brush. With all in place, then reattach your showerhead by fitting all the screws in place.

Recommend reading: Top 5 Best Delta Square Shower Heads Reviews 

 


Easy-to-follow Instructional Videos

Recommend reading: The 9 Best Delta H2okinetic Showerhead Reviews

 


Further Tips

Read more on different types of water flow restrictors and their installation process because understanding the installation will make it easier for you to unscrew it faster and safer.

Any move you make should not damage any pipe fittings and O-ring as they play a major role in your showerhead’s water supply.

Here is our quick tip on how you should remove your water restrictor, try using an electric screwdriver or needle-nose pliers when pulling it out.

Recommend reading: Top 10 Best Bar Mixer Shower Reviews 

 

Factors to Consider When Removing a Water Restrictors

Before you remove your water restrictors, it is wise to consider the type of restrictors installed in your showerhead, the type of showerhead you have, and the O-ring’s safety.

Take cation when handling these parts because they determine the amount of water and water flow in your showerheads. You can find more about different water restrictors and their removal procedure online or hire a specialist to help you replace or remove your restrictor.

Recommend reading: Ultimate Guide on How to Install a Ceiling Mounted Rain Shower Head

 

Conclusion

Removing your water restrictor can vary from on-brand to the other; the guide has outlined some of the basic and proven ways to use it when replacing or to remove your restrictor. But before making any move towards removing, it is wise to find more information about your showerhead design because different designs have different fittings.

Recommend reading: The 6 Best Delta In2ition Shower Head Reviews with Advanced Technology